Shotgunworld.com
http://www.shotgunworld.com/bbs/

Walmart 2013
http://www.shotgunworld.com/bbs/viewtopic.php?f=13&t=328427
Page 1 of 1

Author:  RockedEm [ Sun Jan 27, 2013 9:05 am ]
Post subject:  Walmart 2013

Here we are at the end of the Goose Season in Ohio and as such I'm starting up my reloading for the winter.

Each year I've made it a personal interest to see where the mass loaded cheapies are in their loading components as it floats so much year to year (month to month) in their manufacture.

Boughy and Cut apart the following:
$6.75/bx - Federal Walmart Pack (Maroon/Black,MP12) - 12ga, 2 3/4, 1200fps, 3Dr, 1 1/8Oz
$5.20/bx - Federal Top Gun (Blue Box, TG122) - 12ga, 2 3/4, 1250fps, 3Dr, 1Oz
$5.20/bx - Federal Ultra Clay and Field (Black Box, UC123SI) - 12ga, 2 3/4, 1255fps, 3 1/4Dr, 1 1/8Oz
Winchester Universal (Black Box) - 12ga, 2/34, 1200fps, 3Dr, 1 1/8Oz
$6.75/bx - Walmart Remington Sport Value Pack, Black shell, 7.5shot, 1Oz, 3.25Dr

The $5.20/bx ones I get at a local source by the flat.

Federal - Surprisingly the Ultra Clay and Field have a high brass shell. Thought that was silly, but ALL the Federals are all the same inside. All paper bases, Shot was all dull/deformed, Two piece wads, etc. Will use them to blow up fruit and other fun shoots. Pellet counts were on the light side by okay, however pellet size was all over from about 10's to 6's.

Winchester Universal - Surprised me, one piece wads (cheap but better than federal), shot was all more uniform than Federal, dark and shiny. A few deformed and cut in half, but would choose this over Federals by the looks. Base wad was plastic two piece.

Remington Value Pack (Green Box, Black Shells) - I didn't retain the box, I just took one from a buddy, but I'm going to probably go with these this year as I reload after shooting (usually only once with this ammo). Remington also had a one piece wad and what was more important to me, the Remington Value Pack shell was a one-piece compression formed hull!?! Pellets were nice dark and uniform in roundness and size with a couple that had a flat. Once piece wad. Of the 3 I cut open one had petals that were not slit through at the top beween at least one petal. So you may be shooting slugs at some targets and not know it.

The Remington hull has got my interest. I went downstairs and dug out an STS cut away and put the calipers all over them down to the base and by god I can't see a difference other than a bit more variation and thinner side wall thickness and the value pack.

In the end, what your store has may vary lot to lot, but thought I'd share.

In the end I would go with AA's or STS when its important and I can gather hulls back easily (down to my last fifty original AA compression hulls on about the last reload (9). Remingtons on the skeet range for reload.
Winchesters if nothing else.
Federals I will reload once maybe, but use them in scenarios where I probably can't get shells back.

Author:  mtgrs737 [ Sun Jan 27, 2013 9:28 pm ]
Post subject:  Re: Walmart 2013

Nice report, it is always good to know what cheap shells contain, so we can make an informed choice. I cut open a STS shell and it had the joined at the top wad petals thing going on as well, I doubt that it stays joined though after it gets that rocket ride down the barrel. I was suprised to see a couple of football shaped lead pellets in the load after all I have always thought that STS were the best in target shells. Live and learn!

Author:  RockedEm [ Mon Jan 28, 2013 7:19 am ]
Post subject:  Re: Walmart 2013

Sounds like the same components may be used in some of the lower end remingtons then as the STS.

Upon closer inspection of the Remington wad there is flash hanging about 1/32-1/16" over the top of where the wad is supposed to end in the mold.

So the slitter went up to the appropriate height but they this flash is on top connecting htem (it is tough material).

The material left connecting the petals approximate to a slightly softer/thinner version of a nylon cord that they use to connect price tags.

Pretty tough to break by hand through the flash.

RockedEm

Author:  Shoot2reload [ Mon Jan 28, 2013 7:27 am ]
Post subject:  Re: Walmart 2013

Remington wads are purposefully stitched. It's done for ease of loading, particularly with fast commercial loading machines. Put 10000psi behind them and they'll break.

Author:  marshal kane [ Mon Jan 28, 2013 8:13 am ]
Post subject:  Re: Walmart 2013

RockedEm wrote:
. . . So the slitter went up to the appropriate height but they this flash is on top connecting htem (it is tough material).

The material left connecting the petals approximate to a slightly softer/thinner version of a nylon cord that they use to connect price tags.

Pretty tough to break by hand through the flash.

RockedEm

Probably the flash has something to do with it but when I reload STS it's 1 1/8 oz. #8s with OEM Remington fig 8 wads and as I slip the wad under the shot tube, a petal connector always breaks so I'm pretty confident that the connectors (at least with this wad) will break as the payload goes down the tube.

Page 1 of 1 All times are UTC - 6 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/